2002 TunerPro Bin Files
2002 TunerPro XDF 12212156 OS
Printable View
2002 TunerPro Bin Files
2002 TunerPro XDF 12212156 OS
2002
http://www.gearhead-efi.com/Fuel-Inj...attach/bin.gif '02 Chevy 2500 4x4 8.1 L18 os12216125.bin (512.0 KB)
http://www.gearhead-efi.com/Fuel-Inj...attach/bin.gif '02 Chevy K1500 5.3L os12216125.bin (512.0 KB)
3 more from the 60V6 forum.
I can't open this in TunerPro because I don't have the definition file for it (27_06).
But I can open it in TunerCat, it uses definition 27_06.
....
....
These are both from 02 C6500 GMC's with the 8.1l, but an AT545 non electronic automatic. You can segment swap them over for swaps using a non electronic auto(700r4, th350, th400, and so on). Unfortunately they only used the 2088 and 6125 with the DBW 8.1L.
2002 Silverado 2500HD 6.0L NV4500 5spd manual 4x4 stock bin read from 411 ECM 2156 OS (VIN changed and VATS disabled)
Hi, im trying to download the bin file for 5.3 manual trans and it keeps coming through as a adobe document, I need it as a XDF file. any help?? thanks, Mark
Hi im looking for 2002 Chevrolet Express Van L31 5.7 Litre 4L60 4x4 (12212156).bin . or will the 2wd bin
Hi im looking for 2002 Chevrolet Express Van L31 5.7 Litre 4L60 4x4 (12212156).bin . or will the 2wd bin
Hello,
The 4X4 vans were built from a 2wd van by an outside contractor. You should start with a 2wd .bin file.
Hello! so, what did you come up with? I see the 2wd version on here. That's also what I am operating with, however I am converting it to manual. Did you figure out a 4wd, for that is part of what I got going on!
I have a 411 PCM and I used PCM Hammer to update it to the 2156 OS. I am swapping a Gen 3 5.3 V8 with 4L80 into a Dodge. I would like to segment swap the 4L80 portion since that combo was never sold by GM. I see the only 2156 file with a 4L80 here is for a pre-LS (L31) Express van. Can I use that file for the segment swap?
Thanks.
UPDATE
I used LS Droid to segment swap the Van 4L80 file (see below), and PCM Hammer to write it to my 411 PCM- no errors. I did the transmission and transmission diagnostics. The base file was the 2002 Silverado 5.3 DBC no EGR from post #8, I modified it by changing the tach output from 6/6 to 3/3 and disabled some MIL codes for the rear O2 sensors. I'll update here if it works, I'm still a ways from starting my swapped engine. I'm attaching the new bin file.
UPDATE #2
When I checked the segment swapped file with HP Tuners, it showed as backwards- the engine was a 5.7 not 5.3, and the trans was a 4L60, not 4L80. As such, I don't think this file is usable as-is.
UPDATE #3
I found my error was in LS Droid. I presumed the green button meant you were swapping that function, and the red one meant you were not. That's backwards. I deleted the file until I can fix it.
UPDATE #4 11/7/20
Updated file attached. My truck developed a mechanical problem (oil leak), but the tune allowed it to run OK. As I recall, it has a number of MIL codes disabled such as EGR and secondary O2 sensors, AC and VATS are disabled, and the tach hi/low resolutions were modified. I was not able to drive the truck to verify the trans shifted properly, so use at your own risk. It did show up as a 5.3/4L80 in HP Tuners though. :thumbsup:
Any luck on swapping the 5.3/4l80 combo yet? I could use it if it's done
Just updated the prior post with the revised file. Give it a try and let me know how it goes, I'm down for at least a couple of weeks.
Possibly someone will share a stock 2002 Camaro LS1 with Manual .bin :thumbsup:
Thanks in advance,
dave w
A little off reach of the thread but hth's
My hero. This is the exact file I was looking for.
Hi Guys, im very new here, these are what i can contribute for now all stock
Thank you! Great way to begin.
I’m looking for 5.3, 2wd, 4L60E, truck MAF and stock LS1 intake calibration/bin.
I am needing a 2002 LS1 w/Auto trans bin. If anybody can help me out with this I will be forever in your debt!
Whatever happened with the segment swapped 5.3 4L80e? Regardless, I just recently grabbed a PCM from a 2002 YukonXL with an LQ4 (verified pistons) with an AWD 4l60e/65e not sure which. It is also DBW. This is the stock tune pulled with PCM Hammer.
12212156 is supposed to be universal, but before I screw anything up does anyone happen to have a 2002 Chevy Astro AWD with 4l60e bin? I'm fairly confident I can just use whatever 12212156 that is close and simply copy over everything but I'd really like to start out with a known astro/safari bin if at all possible. I'll straight up paypal someone $5 if that is allowed.
removed
Thanks for the file post, was what i needed for a th400 to lq4 pairing!
Your 2088.bin file id's as a 8322 OS with PCM BIN Builder. Just wondering if you were aware of this. As I had to use a 8322 OS to get the segment swap to not throw a mismatched OS and would not complete with a 2088.bin file. Again thanks,
Good night friend, I am very very new to tunerpro and I would like to learn a bit I have downloaded a bin file right now but I see that it is asking me for the XDF file which I do not have, I did not know I am in the right direction asking for help in this way or in estge forum place
The question is where do I get the XDF from, do I have to ask for it exactly for each ecu?
Hello all. We are performing a PCM upgrade for a customer from a 1996 black box Vortec PCM to a 2002 "0411" OS 12212156. Mainly to accommodate tire/gear changes, etc. Anywho. The project truck is fitted with a 5.0L Auto setup. Big deal right? Who cares about a 5.0L? Well, this customer does and we accommodate. I searched and was unable to locate a good 5.0L bin, especially for a 2002 OS. I broke down and "bought" a bin from GM via SPS2, flashed a spare PCM and voila, 2002 5.0L bin. Since I could not find a good 5.0L .bin, I am sharing the one I have with the world. Enjoy. I make no warranty expressed or implied, it is a stock GM binary.
Bill
edit: This binary is originally from a 2002 Express van 5.0L 2wd.