Thank you again for your detailed response! I'll look into putting something in place for the CPP switch....maybe a relay off of the cruise clutch switch.
My cruise module is off of a 2000...
Type: Posts; User: Scott68B
Thank you again for your detailed response! I'll look into putting something in place for the CPP switch....maybe a relay off of the cruise clutch switch.
My cruise module is off of a 2000...
Thank you for the response, I really appreciate it!Yes, it is manual transmission tune but I don't have a switch on the clutch. I'm right in the middle of installing factory cruise in the car so...
This is probably the wrong place to ask this but i'm wondering what table(s) defined in these XDFs one would use to adjust how fast the RPMs drop off in between shifts on a manual car? i'm using a...
Wow!Thank you for sharing this! Can't wait to to get it on my laptop.
It appears to be a different application. If you read the thread I referenced above you'll see the author adapted an app he wrote for the blackbox PCM to the 0411.
I haven't gotten it to work yet either but I don't need it yet. I tried it first on my XP laptop and got the same thing. Tried it on my Windows 7 machine and it wanted the .NET framework installed. I...
I'm sure everyone knows about this by now but I don't see it here so I'll post it:
http://www.thirdgen.org/forums/diy-prom/696609-houston-we-have-reflash-4.html#post5844169
Does anyone have any...
Did some further searching and found the thread I was looking for. I think the last post in this thread gives some hope. :)
http://pcmhacking.net/forums/viewtopic.php?f=10&t=1320
Shit, I didn't realize that. I got an ADX off the pcmhacking site a few years ago along with a cheap ELM cable and was able to log my friends 96 LT4 Vette with Tunerpro 5. It was pretty simple but it...
I'm sure this has been asked/answered before but I can't seem to find it. I'm in the process of creating a wiring harness for my LS4. My 0411 came out of a 2001 S-10 4.3. I believe I have all the...
Count me in for a cable and the full blown 'write' software when they are available.
Thank you, I appreciate your response. Interesting image.
I'm going to be using an 0411 PCM in my upcoming LS4 swap. (I was considering going OBD1 but thought better of it.) I was wondering if someone knew what signal from the cam sensor the PCM is looking...
I'm suggesting powering down the PCM while burning the chip.
I'm sure this is a dumb idea but what about leaving the chip in place on the board but solder the Moates solder-on header directly to the pins on the chip. You could plug a ribbon in on the PCM side...
Thanks for all the information! Really helpful here.
Regards
Scott
I should have explained my situation a little better. I've got an old MGB with a 3.1 V6 in it now and I'm going to be upgrading to an LS4 in the not too distant future. I believe the best route for...
Would there be any issues with controlling fuel only, no spark, with code like $8D?
Scott
Thank you for the information! It's a big help.
Regards
Scott
Sorry for the delay in responding. I finally got out to the garage and tested my injectors. They averaged about 11.5 ohms. So does that mean they're high or low....as far as the 7727 is concerned?
...
Thanks for the response everyone. There will be 8 of them and they're on a 2006 5.3 LS motor. I will have to test them. If needed, does anyone know the part no. for the injector driver?
Thanks...
I did do a search but didn't get a definitive answer so pardon the question if it has already been answered.
I'll be doing an engine swap at some point in the not too distant future and I'm...