I'm sorry, I said location, that is the wrong term since it's not changing a value in a bin file. I'm still not sure what that number is called. address?
anyways, I'll take a look at that patch...
Type: Posts; User: ???
I'm sorry, I said location, that is the wrong term since it's not changing a value in a bin file. I'm still not sure what that number is called. address?
anyways, I'll take a look at that patch...
so this might be the wrong location, but is there a way to find a location of a pid you want to log from another scan tool? like I have pids from other places on the net, add them to torque app and...
that's a shame, I was playing around with it, since I already had a Bluetooth one. tp connects to it when I use the wrong adx, just no useful data of course. but when I the to use the adx for obd2...
I'm no help on the tuning side, all I remember from the emissions testing days, back before we could turn anything. just bolted on parts and went lol. but adding a electric smog pump from the lt1....
just thought I'd add real quick that it might be useful to pick up the pwm box from I believe it's a Ford something. it's the same box the c6 corvettes use but at cheap price and in junk yards. that...
the 7730 ecm only had one injector driver, so by batch fire they mean all 8 at a time. the 7749 had 2 drivers which is why they can be modified to do low impedance.
injector timing isn't all that...
that's might just be a very fun car to drive. I have a soft spot for the old t5 in the world of t56 swap everything lol.
what are you trying to do wtih it turning wise
did you ever get in? looks like some posts from 2018. it's pretty dead but maybe not completely.
the syty forum might be a better place.
ah. didn't realize it was so new of a ecm. even though you out the ecm number lol I didn't look it up.
as for adding to the ads, yeah. that's a bit over me too. you'd need the location and the...
can you connect to the aldl? sometime the light can be on in limp home mode and still run well enough to know always know. but thealdl ccan't connect to the ecm.
it very well could be a code...
pretty much everything I've messed with. the ecm doesn't do anything for gauges besides the speedo output on some. there's normally extra sensors on the engine run straight to things like coolent...
random thought, I know nothing of the mask you're running but is the o2 in a header and a one wire? maybe it's getting at idle?
has a tpi car drive me nuts once over that.
should it running off a stock tune? like have you loaded up a known good bin for this setup?
cause if you're trying to run a boat motor off a stock truck chip. wouldn't it require tuning?...
in my experience with the wheel. it seemed pretty sensitive. a buddy hand cut one, it was a bit thinner and touch bigger but still square corners. the car ran but timing wasn't right. if you invest...
that's good. sounds like you just need to start tuning. again, I know nothing about this ecm tbi tuning, so you might wanna find a thread about the logical order to start tuning it.
without...
you could disconnect the injector but I doubt it matters. just have someone fire it up and be ready with the spray, just use short bursts and see if it stays running. don't over use the stuff. you...
I have zero experience with tbi but could you just need to tune it? like the cranking fule is correct but the idle ve or coolant temp table off a lot?
have you tried the old trick of running it...
I had a pick up coil in a camaro years ago get me. I don't remember what ohm, but the book gave me a number and then leave it hooked up and spin the distributor and the ohm value should move. if I...
http://www.amazon.com/SainSmart-Portable-Handheld-Digital-Oscilloscope/dp/B018E4AJH2?ie=UTF8&ref_=cm_sw_r_awd_7fUdxbYPQX1KW
so I picked up one of these for a project and it has a built-in wave...
yeah you'd have to put the rotor and optical pickup in a dizzy and then run the n* coil packs. or something. and then the dizzy runs half speed of the cam if I'm thinking of that right?
we did...
you're right never realized there was a inner part of the wheel for the cam location and the other.
yeah, thst totally won't work then. shame ccause it would have been nice.
wow this thread moved fast. I skimmed thru a lot because I hate to just dive in a thread and ask a questiontthat doesn't make any sense lol but here goes.
is there a link where I can look for...
hey six shorter, I'm tossing around the idea of a 749 sswap onto a car that has stock low z injectors, that I know nothing about. not even flow ratings anywhere I can find haha. what kinda strategy...