https://ecmhack.com/trimalyzer/
Website from member on here steavo,
He created trimalyzer
Type: Posts; User: ralmo94
https://ecmhack.com/trimalyzer/
Website from member on here steavo,
He created trimalyzer
This is correct, if both are not below set value, it will use open throttle ve table. That is why I like to use trimalyzer to tune VE, you can just set a filter for idle flag false, then go back and...
With the IAC closed and unplugged, yes it should run at where ever the butterfly stop is set, but that still wouldn't tell you why the ECU is requesting 1k idle speed. It may be a worthwhile test to...
Like he said said, you need the proper definition files for tuner pro, otherwise it's like trying to decipher Greek with a Spanish English dictionary.
You need to know what mask your ECU is using,...
Any updates?
As far as I can tell it's for a 350 manual trans and the right mask, I don't see why it wouldn't work.
:rockon:
If it smells rich out of the pipe and the O2 is saying it's too rich, I'd say there is a rich condition, and replacing the O2 is kinda like shooting the messenger.
That's why I suggested...
As far as I know everything is in the bin for it, just have to add pins to the PCM connector and install one if wanted. Some have, and it is said to be better with a MAT rather than IAT as it's a...
As far as I know, your ECU will read any prom with the same mask, I had been told previously that the releases of new BCC codes were incremental meaning Ab superspeeds AA. But I have also been told...
TBI does not have IAT, or MAT. It uses engine coolant temp.
Good to hear. Hope it continues to work as smoothly as reported now. :happy::rockon:
Certainly not to much to ask for. Lol.
Yes you can swap a 7427 if you would like, you would need a PCM, the two connectors and a memcal, and a chip to burn, I don't recommend using a memcal adapter...
I would check fuel pressure. They make a special gauge for TBI that goes between the return line and the TBI.
Does he have any codes?
It appears it has been trying to lean the mixture to the extent it's allowed with a 111 BLM or long term, and it's open loop, short term is 128, 128 - no adjustment. ...
The more data is from the 7427 PCM, or equivalent service number.
I personally am wondering about the prom, if it's stock, or uncorrupted. Optimal thing would be if you had another prom to...
Nice F body
If you haven't already, you should check out steavo's site
Ecmhack.com
He is a member on here who has created free to use tools for that platform
Yes the starter wire should definitely not be hot all the time, if you find it, I'll bet you also find the source of the arc. Hope it's an easy fix for you.
This might help with the cylinder select knowledge.
http://www.gearhead-efi.com/Fuel-Injection/showthread.php?454-What-If-8D-(1227727-ECM)-for-TBI&p=3374&viewfull=1#post3374
Also, when you use...
So the starter wire is hot all the time? I would suspect a faulty ignition switch. Unless its hot after the relay, then I would suspect a sticky relay, they do stick sometimes.
Then of course...
Nice looking jeep, and nice canoe's.
While port would be an advancement, I see no real world advantage over TBI, as long as it suits your rpm and cfm requirements, but a modded Clifford intake...
Glad to hear. Too many repairable trucks end up in the scrap yard and are replaced with new trucks that aren't made as good. Well that's my opinion.
Was the truck operation before the swap?
If so, was the purple wire going to the starter?
Iirc in 93, the wire went right from the ignition switch to the starter solenoid without the fuse box
Hope it works for you, if not, you may need to verify your wiring :popcorn:
:popcorn: