Search:

Type: Posts; User: silvergs

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    2,793

    Accelerator "pump shot"

    Does anyone know what table controls the "accelerator pump shot" on a 2002 truck ecm? I am using this setup on another brand motor and need to richen up the fuel on a throttle transition.

    Mike
  2. Thread: Cam Signals

    by silvergs
    Replies
    7
    Views
    13,795

    Unfortunately I don't have another sensor to try....

    Unfortunately I don't have another sensor to try. This is a new sensor but that doesn't mean anything. I am leaning towards something about the signal going into the ecm not having enough "load" to...
  3. Thread: Cam Signals

    by silvergs
    Replies
    7
    Views
    13,795

    P0343

    P0343
  4. Thread: Cam Signals

    by silvergs
    Replies
    7
    Views
    13,795

    Scott, The VOM meter shows 12V high and 0V low...

    Scott,

    The VOM meter shows 12V high and 0V low but still sets the code. Wish I had access to an o-scope.

    For the crank sensor I just took a stock ls 24 wheel and mounted it on my bottom belt...
  5. Thread: Cam Signals

    by silvergs
    Replies
    7
    Views
    13,795

    Cam Signals

    I have a Buick 455 with a 4L80E running on a LS 411 ecm. I am using a Grand National distributor that I have cut half the "hat" so it gives a signal of 180 on and 180 off. It runs good but will set...
  6. Replies
    13
    Views
    12,162

    Skinny Pedel hit it. I didn't have the timing up...

    Skinny Pedel hit it. I didn't have the timing up far enough on the high KPA side. It started to come around and then suddenly got a no start issue. Well after a lot of messing around with...
  7. Replies
    13
    Views
    12,162

    Here's the latest file. I just can't figure out...

    Here's the latest file. I just can't figure out why the timing is dropping off so far at an idle. Haven't gone through much more than that at this time.
  8. Replies
    13
    Views
    12,162

    Thanks for the feedback guys. I know its a bad...

    Thanks for the feedback guys. I know its a bad choice for a cam but it is what he put in.

    I have the idle timing set at about 30 but it never gets over 10 or 11. Don't know why. I will hook the...
  9. Replies
    13
    Views
    12,162

    Idle timing on a cammed 97 L31

    Got a customer that dropped off a 1997 1/2 ton that he rebuilt the motor on and installed a "Thumper" cam. Bad choice on his part but I am trying to get it to idle and run halfway descent. My issue...
  10. Replies
    24
    Views
    16,565

    Playtoy I helped my nephew put a 6.0 in a 89...

    Playtoy

    I helped my nephew put a 6.0 in a 89 Camaro. We redid the harness and got it running pretty good. (12.50's on street tires) While playing with it I tried to flash a Camaro os into it to...
  11. Thread: Monodax

    by silvergs
    Replies
    56
    Views
    58,984

    Thanks Hog I have a couple of supercharged...

    Thanks Hog

    I have a couple of supercharged applications coming up and will need some custom help on them.

    Mike
  12. Thread: Monodax

    by silvergs
    Replies
    56
    Views
    58,984

    Hog You have any idea when the Monodax forum...

    Hog

    You have any idea when the Monodax forum will be back up? Theres a lot of information there that I would hate to lose.

    Mike
Results 1 to 12 of 12