I was just thinking that very thing. Basically copy over the change log as well.
I was just thinking that very thing. Basically copy over the change log as well.
The man who says something is impossible, is usually interrupted by the man doing it.
probably isn't a bad idea..... i'll do an edit in a minute.
it could be some kind of placebo effect(or perhaps some kind of uncluttering occurred), but this release feels SUPER responsive.
took a minute to reconfigure some of the stuff that got reset upon install, but otherwise.....
I think it's placebo, Feels the same as it has for a long while now, to me.
The man who says something is impossible, is usually interrupted by the man doing it.
'Fixed issue where when comparing bins in a 3D chart, axes were
not updated apporpriately when they are defined internally"
This mean the 3d maps match the 2d's? That drives me nutts lol
89 K1500 Scottsdale 5.7L 5spd 3:42 RamJet cam Dart iron TBI heads 427 PCM swap
95 C2500 Cheyenne 6.5L turbo diesel 4L80e 4:10 DB2-4911 Manual pump conversion 0411 PCM trans control 2Bar COS
05 Outback XT 2.5L turbo gas auto
5.00.8383.00 (General Release) (4/30/14)
- Fixed issue where a particular piece of hardware wasn't
properly detected- Fixed issue introduced in build 8369 where Moates Ostrich 2.0
address watch (tracing) used incorrect addressing- Fixed issue with ELM327 plug-in where first byte of 2-byte PID
was always 0- Updated ELM327 plug-in version number to 0.6
5.00.8414.00 (General Release) (8/25/14)
- Fixed issue that prevented tables from being saved when a base
offset is used that results in the table's unadjusted address being outside of
the bin- Fixed issue where editing XDF table properties in the XDF
editor while the table is open didn't result in the table reflecting the changes- Fixed issue where adding a new ADX item, then immediately
dragging it to a new index in the tree without setting an ID, would result in an
endless loop of errors
Known issue to be fixed in next build:
- issue that may cause table axis links not to be resolved
on XDF load
5.00.8519.00 (General Release) (11/19/14)
- XDF Item Finder toolbox is now resizeable
- When a table graph is open and a new compare bin is loaded from the compare menu, the graph is now refreshed to show the new bin
- When opening a new XDF with the XDF Item Finder toolbox open, the toolbox is now automatically closed
- Fixed crash when attempting to connect to ALDL stream in AutoProm mode with no AutoProm attached to the PC
- Fixed issue with keyboard shortcut assignment where attempting to assign the Escape key resulted in the shortcut window closing instead of assignment of the key itself
- Fixed issue where choosing "Save As..." when saving an ADX didn't cause the editor title bar to update with the new filename and path
- Fixed issue where recursion in a table or function equation wasn't properly being tracked and reported, resulting in over-reporting of recursion
- Fixed a subtle but particularly heinous bug where XDF conversion equations that were recursive could result in variables with the same name being overwritten during recursive calculation (e.g. "CELL(ROW()+1; 0; FALSE) - X", where the value of X is set in the initial calculation frame, then overwritten when the CELL function is called with the value of X in that calculation frame))
- Fixed issue with patches that would falsely report a buffer is patched when a portion of it is not actually patched
- Fixed issue where table axis links may not always be resolved on XDF load. Current fix has very minor performance implication with large XDFs. Future improvement planned.
5.00.8606.00 (General Release) (3/17/15)
Exposed the ability to specify an ADX command to send when scanning is paused and unpaused. This required that the ADX Defaults be moved to the "More" tab in the ADX Header editor.
Made vast improvements to the Moates Onboard Logger interface (for the Demon and Superlogger hardware), including multi-threading to keep the UI from locking up during long operations, auto-population of ADX for export, flash memory export to and import from file, and much more
Added a very naive XDF parameter bulk editor. It will change endianness, sign, and will offset specified positive or negative amount all address equal to or greater than the offset
Fixed issue where passing in a checksum element size less than 8 bits could result in an infinite loop during checksum calcutation
Fixed issue where ADX List View separaters weren't being updated in real-time in the ADX editor while typing or changing separator text color
Fixed issue where function graphs couldn't be interacted with
Fixed issue where command timeouts weren't being passed to the port when running in shared emulator<->dataAcq mode
The man who says something is impossible, is usually interrupted by the man doing it.
Bookmarks