Page 1 of 2 12 LastLast
Results 1 to 15 of 20

Thread: God I hope im doing this right

  1. #1
    Electronic Ignition!
    Join Date
    Jul 2016
    Age
    50
    Posts
    12

    Question God I hope im doing this right

    So i put a tbi kit on my jeep 258. Working on getting tunerpro rt set up. I dont know right from wrong here. Ive downloaded the .bin, .xdf, and .adx files and have them in tunerpro. Im scared to death im going to screw something up. Is it possible to damage something if i have the incorrect files installed? I dont know where to begin. Any help would be great to get me going.

  2. #2
    Fuel Injected! jim_in_dorris's Avatar
    Join Date
    Dec 2011
    Posts
    803
    No, your data would be garbage, but no damage
    Square body stepsides forever!!!

  3. #3
    Electronic Ignition!
    Join Date
    Jul 2016
    Age
    50
    Posts
    12
    That's good to know. Got it all set up last night, tried to connect and the connect bar got stuck connecting...Any ideas?
    Last edited by bubbafreejohn; 07-14-2016 at 05:28 PM.

  4. #4
    Fuel Injected! jim_in_dorris's Avatar
    Join Date
    Dec 2011
    Posts
    803
    What ecm and files are you using
    Square body stepsides forever!!!

  5. #5
    Electronic Ignition!
    Join Date
    Jul 2016
    Age
    50
    Posts
    12
    the ecm is a 7747, apab $42-4.3 manual .bin, $42-1227747-v5.9.3.xdf, and $42-1227747-v5.2.adx, was outside and managed to get it to connect, then after about a minute the rpm's jumped from 750 to 1800 on their own,,,,freaked me out, shut it down. I think i need to try v3.adx.
    Last edited by bubbafreejohn; 07-15-2016 at 06:06 PM.

  6. #6
    Fuel Injected!
    Join Date
    Sep 2012
    Location
    washington indiana
    Age
    69
    Posts
    884
    is your vehical a 4.3 standard trans? that is what mine is and the adx an xdf worked okay but I removed it then reinstalled, are you running xp 7 or windows 10?

  7. #7
    Electronic Ignition!
    Join Date
    Jul 2016
    Age
    50
    Posts
    12
    the tranny is a ax-15 5 speed, i did some tinkering around and finally got it hooked up and did a bit of recording. My first question would be my knock count, since i dont have a knock sensor, second and probably most important is the timing advance. It starts fine, then the advance ramps up, and up, and up, off the chart above 35 degrees. then after about 50 seconds to a minute, the timing falls flat to zero, and slowly climbs back up repeating the process. those two things are all i could see, and the async! operation, not sure what that is. Is there a way to change that timing from doing that, it has a misfire at idle, or acts like one. and its driving me crazy. Pardon my rant, but to answer your question, windows 10, here are some screen shots i took. Attachment 10763Attachment 10764Attachment 10765Attachment 10766
    Last edited by bubbafreejohn; 07-17-2016 at 06:52 AM.

  8. #8
    Fuel Injected!
    Join Date
    Sep 2012
    Location
    washington indiana
    Age
    69
    Posts
    884
    it will do that until you burn a chip and apply the bpw and spark patch from the paremeter tree. I don't think it is aculy advancing it is just being read wrong.

  9. #9
    Electronic Ignition!
    Join Date
    Jul 2016
    Age
    50
    Posts
    12
    How, if possible, can i turn off knock?

  10. #10
    Fuel Injected!
    Join Date
    Sep 2012
    Location
    washington indiana
    Age
    69
    Posts
    884
    there is a member on here that has a set up like yours I can't think of his name but he could give you a bunch of help,jim might remember him he works at a john deere dealer I think in Georgia or luisianna

  11. #11
    Electronic Ignition!
    Join Date
    Jul 2016
    Age
    50
    Posts
    12
    Quote Originally Posted by ony View Post
    it will do that until you burn a chip and apply the bpw and spark patch from the paremeter tree. I don't think it is aculy advancing it is just being read wrong.
    i applied the bpw patch from the tree, disabled egr, what should i do next, how do i burn a chip?
    Last edited by bubbafreejohn; 07-19-2016 at 04:11 AM.

  12. #12
    Electronic Ignition!
    Join Date
    Jul 2016
    Age
    50
    Posts
    12
    ony, that would be great if you could remember his name. Maybe it'll come back to you

  13. #13
    Fuel Injected!
    Join Date
    Sep 2012
    Location
    washington indiana
    Age
    69
    Posts
    884
    jeeps an guns is his name, I think he has 2 jeeps that he changed to chevy efi.

  14. #14
    Fuel Injected!
    Join Date
    Sep 2012
    Location
    washington indiana
    Age
    69
    Posts
    884
    you need a chip programmer to burn chips.or have someone do it for you.

  15. #15
    Electronic Ignition!
    Join Date
    Jul 2016
    Age
    50
    Posts
    12
    you can't do it with tuner pro?

Similar Threads

  1. Replies: 3
    Last Post: 06-26-2013, 07:17 PM
  2. Replies: 2
    Last Post: 05-20-2013, 06:52 AM
  3. helpme obd1 your my only hope /so what do i need
    By swat455 in forum GM EFI Systems
    Replies: 8
    Last Post: 03-29-2013, 08:57 AM
  4. help me obd 1 your my only hope
    By swat455 in forum TunerPro Tuning Talk
    Replies: 7
    Last Post: 04-30-2012, 03:35 AM
  5. DIY-EFI RIP? I hope not...
    By EagleMark in forum GM EFI Systems
    Replies: 5
    Last Post: 01-03-2012, 09:26 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •