what am i doing wrong?

**CapriceLT1** · 05-07-2012

Hey guys,I have a 95 9C1 (LT1 motor). I downloaded Tuner-pro RT and registered it. I have the these bins/xdf's/adx's for it.

From the find your xdf and adx look up. All are at the top of my screen ready to go but it seems like im missing something but I cant figure it out there is so much on there!! Everything initializes and says its ready except the DA?The DA is not linking or w/e (dont have the screen in front of me) its the yellow part at the bottom about 4 boxes in.  Everything else links up. The graphs/dash does not read anything, it just stays still. I can not read anything on the dash or view any graphs while key is on or car is running. did i forget to download something??

**CapriceLT1** · 05-07-2012

Like, all the gauges read zero...do i have to mask something? or does the one file already mask it....pulling at straws since i have no idea what the problem is lol. These arnt mine, i copied the pic from the site so you guys might get a better understanding of what im talking about

**jrgcjnl** · 05-08-2012

first of all you need to make sure your cable is on a com port (under device manager)
if it is, then open up tunerpro then open up preferences under tools at the top
then under data acquisition click configure plug in component
then make sure the com port there matches the one on your cable, then press ok
then next to the ADX settings at the top toolbar, click the two blue arrows and see if that works, if the data is unstable (not reading correctly but still moving crazily) go ahead and click it again, wait about 2-3 seconds and try again, if not
keep retrying until you have smooth accurate data
that should be it

**EagleMark** · 05-08-2012

With your cable plugged in restart computer. Then open TunerPro and go to Tools, Preferences, Data Acq/Emulation and choose Plug in, then Configure Plug In Component and see if it is on the right Com port. Then test cable. Do this while not hooked to car. If it finds cable move on. If not move cable to another USB port and try again. If you run out of USB ports then look to see what Com port it is on. Start, Devices and Printers, find the cable, right click and properties.

LT1 comes in a few different cars and they have different modules on the ALDL line. Depending on car some need to be connected, disconnected and connected again to get good data the way this ADX file is set up. But that is usually bad data, I think your cable is not installed correctly or configured correctly in TunerPro.

**CapriceLT1** · 05-08-2012

Alright. I did as you guys said. I'm getting farther but still hitting bumps...I'm just going to list everything im doing

-Data Acquisition is plug in configuration; Standard serial-Cable found and functional in COM 5 (while plugged and unplugged)
-Initialized Hardware (Found) NEMUv86.254N
-DA Connected then it started flashing (on the DA part) that there were errors and it started counting them for a while.
-I was able to start Emulating but it said "I think you are mistaken" did you mean Bank 8? but i can only choose banks 0,1, and 2. After I try to stop something the emulating keeps going along with the DA Acquisition and the Plug in in still initialized but the Blue button that starts the emulation goes away and i cant hit it again so i restart and do everything over again hoping it will change but it doesn't. Definitely farther than i got before. I still can not get the dash to turn on or data to run and i believe it is because of the DA errors that keep being found. But I don't know what they are, how to find them and how to fix them.

Did you say i may need another ADX?

**CapriceLT1** · 05-08-2012

Sorry for the bad quality, its from my cell phone. Just trying to give you guys as much info as I can. In the first vid i revved the engine up twice to about 5k