Results 1 to 10 of 10

Thread: Hello - How's it going?

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Fuel Injected!
    Join Date
    Nov 2019
    Location
    Bossier City, Louisiana
    Age
    65
    Posts
    339
    I also use the VCX Nano USB wired version and the OBDLink MX Bluetooth ELM327 device but I think the MX+ is what is around for purchase these days.

    Rick
    1970 Chevy El Camino, LM7 Engine, 4L60E - Two 896 and two 0411 PCM's

  2. #2
    Carb and Points!
    Join Date
    Oct 2019
    Posts
    4
    Holy bummers...

    Amazon has them for $119+ USD. Damn, I was hoping for around $20-ish (so I don't have to ask the wife...lol). Looks like this project will be put on the back burner again as I've already put quite a bit of $$ into it and now I "should" have what I need to get it running...till now...unless anyone knows of some software that will pull the BIN from the ECM and burn the modified BIN back using the OBD2 devices I already have...?

    Thank you all for the replies.
    Last edited by Spine; 07-15-2021 at 02:13 AM.

  3. #3
    Fuel Injected!
    Join Date
    Nov 2017
    Location
    Californiacation
    Age
    57
    Posts
    834
    I have many many programming devices, this is the cheapest one and use it with its' software as a generic scanner for non GM stuff. OBDLink SX usb version $39.95 including shipping in this ebay ad.
    https://www.ebay.com/itm/17113931382...MAAOxy-j9SSf8-
    Keep in mind this and other "elm" type devices are extremely slow so make sure your battery is full.
    -Carl

  4. #4
    Carb and Points!
    Join Date
    Oct 2019
    Posts
    4
    I'll have to look into that one (OBDLink SX). Thank you.

    My primary goal is to disable/remove Passlock/VATS(or whatever the security stuff is) from the ECM so I have a running engine. My secondary goal is to edit the fuel tables and timing and set it up for racing in the '85 TA and twin turbos for my '65 Impala.

    I also use a bench setup, so I don't have to do any "initial" programming inside the vehicle.

    Has anyone had any luck using EFI TunerStudio on a GM ECM? I have a registered version that I used when I was using a custom built ECM for an old rally car I ran.

  5. #5
    Administrator
    Join Date
    May 2011
    Location
    Lakes Region, NH
    Age
    54
    Posts
    3,868
    as anyone had any luck using EFI TunerStudio on a GM ECM? I have a registered version that I used when I was using a custom built ECM for an old rally car I ran.
    Hmm... I believe that software is used for Megasquirt? If so there are technical reasons why that question is not valid. In some ways it is similar to asking "Has anyone had any luck using a map of Dallas to navigate San Francisco?" In other ways it's analogous to "Has anyone had any luck using passenger pigeons to send a fax?" In the first case the information in the GM ecm is not arranged in the same way as the information in Megasquirt. In the second case the method used to deliver information is not the same between the controllers.

Similar Threads

  1. How's it going?
    By alex in forum Introductions
    Replies: 0
    Last Post: 08-17-2016, 10:37 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •