would you be able to test the Dizzy on a distributer machine????
Sadly I do not have one and do not know anyone with one.
I have been digging around in my storage looking for my old original distributor I had in it before this one. I was tempted to swap it back to this distributor and reinstall the 8 pin module and external coil.
However I have turned it upside down and can not find it anywhere.
79 Jeep Cherokee, AMC 401, T-18 manual trans, hydroboost, 16197427 MPFI system---the toy
93 Jeep YJ Wrangler, 4.0L, 5 speed, 8.8 rear, homebrew hub conversion and big brakes, hydroboost, 2.5in OME lift, 31x10.50's---the daily driver
99 Jeep WJ Grand Cherokee limited, 4.0L, auto, 2wd, leather and power everything, 99% stock---the long distance highway ride.
So on sunday afternoon I had a couple hours to spend some time with it.
I pulled the distributor, removed the shaft, chucked it up in my lathe, cut the tack welds off and knocked the old reluctor wheel off it.
I then cleaned the shaft a little and put the spare reluctor wheel on it and tacked it in place.
I reassembled and inspected. Everything looks normal and I do not see any visible issues.
I got it started and the base timing re set and tried driving it. No real change.
The missfire is so light at idle it is hard to tell it is doing it. It is not until you start driving you can feel it. I tried moving and wiggling the wires and grounds and the ecu connectors and wires and could not get any noticeable change. However I can not do that and drive it.
I was running out of time and took it for another quick drive around the yard and the missfire was cutting in and out.
79 Jeep Cherokee, AMC 401, T-18 manual trans, hydroboost, 16197427 MPFI system---the toy
93 Jeep YJ Wrangler, 4.0L, 5 speed, 8.8 rear, homebrew hub conversion and big brakes, hydroboost, 2.5in OME lift, 31x10.50's---the daily driver
99 Jeep WJ Grand Cherokee limited, 4.0L, auto, 2wd, leather and power everything, 99% stock---the long distance highway ride.
Search for somebody with an oscilloscop or have one for yourself. There are cheap ones on te market used or brand new like hantek.With an oscilloscop you may find where the irritation in the current starts. Old school garages have them too.I do not think its a mechanical problem like a broken valve spring.You would have found it already.
I have been watching this post and have some minor thoughts.
Have you taken a water spray bottle and sprayed the harness down? along with plug wires? a little at a time while running while moving the harness around
I have seen plug wires go bad and arc out, but I have also found sensors with hair line cracks that let water in, I also found bad wire harness connectors that way as well.
79 Jeep Cherokee, AMC 401, T-18 manual trans, hydroboost, 16197427 MPFI system---the toy
93 Jeep YJ Wrangler, 4.0L, 5 speed, 8.8 rear, homebrew hub conversion and big brakes, hydroboost, 2.5in OME lift, 31x10.50's---the daily driver
99 Jeep WJ Grand Cherokee limited, 4.0L, auto, 2wd, leather and power everything, 99% stock---the long distance highway ride.
Like already mentioned, if you have a laptop have a look for the hantek1008 or the picoscop 2204 A .The hantek is a 8 channel one while the picoscope has only two channels. Both are about 150 bucks and work pretty well for us nechanics. If you download the picosoftware first, you may see a lot of examples what to measure on a car. Of course you may buy one at a much higher price and become an electronics. :-)
Bookmarks